Coating Inspection Equipment - Paint Inspection

Wire Brush Electrode

Made from very small individual wires, the Wire Brush Electrode meets many different requirements and applications, especially for coated surfaces that are uneven or include fittings, bolts, or...

Silicon Rubber Brushes

Made from a unique combination of silicone rubber and carbon, the Silicone-Rubber Brush Electrode meets many different requirements and applications, both on the pipe and off. The electrode is used...

Half Spring Electrode

Half Circle Electrodes make it easy to go around pipe supports.

Holiday Detector "Stick Type" (same as the DeStearns Model 10/20)

Pulsating Stick Type Holiday Detector with voltage settings from 0.8 to 35 kV in one instrument.  Designed with safety in mind.  The Tinker&Rasor APS is the same as the DeStearns Model 10/20 MODEL:...

AP/W HOLIDAY DETECTOR HIGH VOLTAGE: 800v TO 35kv

NOTE: This unit is identical to the DE STEARNS 14/20 800 volts to 35,000 volts in 1 instrument FEATURES ·

TQC BRESLE TEST

The Bresle Kit – Sodium Chloride Test Kit complies with the ISO 8502-6 and ISO 8502-9 standards that describe the Bresle Method to assess the level of soluble salts using a Bresle patch or Bresle...

X-CUT Template Kit

MTest X-Cut Template Kit.  Simplify X cut testing by using a template.  Includes both a Stainless-Steel Template and a Polyurethane Template.  Both are coated with a nonslip coating.   Includes SS...

TQC CC1000/2000/3000 Adhesion Blades

TQC delivers a wide range of Cross Cut Adhesion knife sizes, available for different coating thicknesses and substrates and according to different standards. Hardness: HRC 58 +/- 2 VF2355

ZERO PLATES

Zero Plates   Zero Plates are available as uncoated precision machined steel or aluminum (6061-T6) in a variety of plate sizes. Order Guide

Coating Thickness Shims

Certified Plastic Shims For use with magnetic, eddy-current and ultrasonic coating thickness gages.(Not intended for use with Type 1 magnetic pull-off type gages)  

Certified Polystyrene Blocks

DeFelsko Certified Polystyrene Test Block Kits DeFelsko Certified Polystyrene Test Block KitsUsed to verify the accuracy and operation of any Type 1 (mechanical) and Type 2 (electronic) magnetic,...

FM Banana Gauge

PosiTest®   Magnetic Coating Thickness Gages for Non-Magnetic Coatings on Steel <

Low Voltage Accessories (LPD AND TQC)

DeFelsko PosiTest LPD Accessory Pack LPDACCPK Includes adaptable sponge hardware and accessories to convert the PosiTest LPD Basic Kit into a PosiTest LPD Complete Kit in a hardshell carrying...

HHD BRUSHES

Flat Wire Brush Electrodes   HHD Flat Brush 51 mm/2"        HHDFLTBRSH2<

HHD SPRINGS

Rolling Spring Electrodes   Rolling Spring Coil for 4" pipe (102 mm) OD     HHDSPRING4

SST KIT P

PosiPatch Starter Kit For use with existing conductivity meters. Try the revolutionary, reusable PosiPatch with a low cost trial pack. The PosiPatch Starter Kit can be purchased with either a...

Defelsko Non-Ferrous Calibration Standards

CERTIFIED COATED METAL PLATES Select the Standard that most closely matches the measuring range of your gage.

Wet Film Wheels

Specially by TQC developed instrument for use on wet lacquers, paint, and coil-coated surfaces. Equipped with a precision roller bearing for smooth rolling over the surface. The wheel has three rims,...

Amine Blush Kit

The TQC Amine Blush Kit is a quick and easy amine blush test. Due to advanced research on suitable media, the TQC Amine Blush Kit is the easiest and quickest on the market. It is based on a double...

TQC Hexagonal Wet Film Combs - microns

The TQC Wet Film Thickness Gauge WG is a hexagonal/octagonal precision measuring comb made of heavy stainless steel. The high-grade stainless steel will not be affected by acid or base elements...

TQC Hexagonal Wet Film Combs - mils

SP4050 TQC Wet Film Thickness Gauge 1-80 mils in 36 steps (6x6) With edge radius check (2mm) for protective ... The TQC Wet Film Thickness Gauge WG is a hexagonal/octagonal precision

SPRING LOADED ROLLER FOR DUST TEST TAPE

The TQC Spring Loaded Roller is used to perform objective dust tests according to ISO 8502-3 and eliminates human error by pressing with a constant force on the dust test tape. The ISO 8502-3...

1 ROLL ADHESIVE ISO TAPE

The TQC Tape For Adhesion Test (ISO 2409:1999) is used to perform a cross cut hatch adhesion test according to ISO 2409:2003 standard. To be used with Cross Cut Adhesion Test Kit CC1000, 

Sponge Tester / Expansion Kit

The TQC Low Voltage Pinhole detector enables the user to inspect various coatings on conductive substrates for small defects such as holidays and pinholes using the ‘wet sponge technique’. The...

Powder Coating Ground Tester

New conveyor ground test with five steps which informs you whether items to be painted are sufficiently grounded. Specially designed for electrostatic coating applications. A poor ground of the...