Coating Inspection Equipment - Paint Inspection

Digi-Sense Temperature/RH Touch Screen Recorder with NIST Traceable Calibration

8GB on board memory provides virtually unlimited data logging capacity Measures, logs, and displays temperature, humidity, and dew point Removable sensor for local or remote measurements using extension cable included Wall mount or desk mount...

4 to 60 mil WFC

TQC INOX High Precision Wet Film Thickness Gauge 4-60 mils in 16 steps (4x4).  Similar to the Nordson in looks and quality but less expensive.

Replacement Tape for the Dust Tape Kit

Dust Tape Kit

The TQC Dust Test Kit according to ISO 8502-3 allows assessment of the quantity and size of dust particles on surfaces prepared for painting. Dust on blast cleaned surfaces can reduce coating adhesion, leading to premature coating failure and...

SP3000 - CROSS HATCH TEMP

The TQC Cross Cut Adhesion Test KIT (Master Paint Plate) is a stainless steel measuring tool that features: a 1 mm, 1.5 mm, 2 mm and 3 mm cross cut adhesion test according NEN-EN-ISO 2409:2003 and ASTM D 3359 (X-cut) Andreas cross. Additional tools Wet...

SUPER-PIG DESTRUCTIVE COATING THICKNESS GAUGE

The TQC SP1100 SuperPIG is a destructive precision tool for inspection and thickness measurement on single or multiple coats on virtually all substrates, including wood, plastics, metals etc. Also observes and measures substrate and film defects. Applies...

SHORE HARDNESS TESTBLOCK KIT

Shore A and D Test Blocks Test Block Type D 25 (Red) Test Block Type D 46 (Black) Test Block Type D 75 (Blue) Test Block Type A 30 (Black) Test Block Type A 50 (Grey) Test Block Type A 75 (Red)

Hate TEST KIT Analog

The HATE Mark VII coating adhesion testers offer the coating industry new capabilities, from the lab technician and paint chemist to the field inspector and corrosion engineer. The adhesion strength specified can now be proved to have been achieved -...

Positest Inspection Kit

PosiTector® Inspection Kits   Select from a variety of gage bodies and probes PosiTector Inspection Kits contain a PosiTector gage body (Standard or Advanced) with 3 probes – coating thickness, environmental and...

Cross Cut Adhesion CC2000 BASIC KIT

The TQC Cross Cut Adhesion Test Basic Cutter is used to test the adhesion of dry coats of paint on their substrate by means of a series of cuts through the coating. Two series of parallel cuts cross angled to each other to obtain a pattern of 25 or 100...

PHASE II SRG-2200 Handheld Surface Roughness Tester

Mini Surface Roughness Testers / Profilometer/ Surface Roughness Gage Model No. SRG-2200 Features The New Phase II SRG-2200 Mini Surface Roughness Tester is a next generation of surface roughness tester developed by the Phase II Metrology...

DeFelsko Surface Profile Probe

PosiTector® SPG   Surface Profile Gages for Blasted Steel, Textured Coatings and Concrete Profile Digital depth micrometer measures and records peak to valley surface profile heights Solvent, acid, oil, water, and dust resistant –...

PosiTest ATA Adhesion Tester

PosiTest® AT   Pull-off Adhesion Testers Measures adhesion of coatings to metal, wood, concrete and other rigid substrates. Select from four Stand-offs - 20 mm, 50 mm, 50x50 mm Tile and 50 mm C1583 Environmentally sealed...

SST Standard or Flex Ring

STANDARD RING - for flat surfaces or curved surfaces over 40 inches in diameter. FLEX RING - For flat or curved surfaces down to 4 inches in diameter. Smaller than list - look at the DeFelsko Bresle patches.    

DOLLY- FLAT

If you have a HATE tester - This is the standard Flat Dolly.  Will also work with the Elcometer 108 Dolly:(304 Stainless Steel)Outside diameter 0.75 inchInside diameter 0.125 inch

Calibration Standard For Surface Profile

DeFelsko Certified SPG Standards Ideal for use in calibration labs Certified and labeled in both Metric and Imperial unitsComes with a Sample Certificate of Accuracy Used to verify the accuracy and operation of surface profile depth micrometers...

DeFelsko Posipatch and Bresle Patch

PosiPatch Reusable patch with Standard or Flexible magnetic ring PosiPatches (24) - for use with PosiTector SST PosiPatch Kits - SSTPATCHP24   PosiPatches (5) - for use with PosiTector SST PosiPatch Kits...

PosiTest ATM Adhesion Tester

  Key Features... Manual hydraulic pump designed to apply smooth and continuous pressure with a single stroke Pull Rate Indicator to manually monitor and adjust the rate of pull Environmentally sealed enclosure – weatherproof, dustproof...

SRG4000 Surface Roughness Testers /Profilometers

Surface Roughness Testers /Profilometers/Surface Roughness Chart Model No. SRG-4000 Features The latest in state-of-the-art surface roughness testers profilometer, the SRG-4000 is designed with the shop environment in mind. These surface...

DeFelsko Posipatch Miscellaneous Accessories

Flexable Dispenser Tips Syringes Syringes with needles Conductivity Standard  

SRG4600 PORTABLE SURFACE ROUGHNESS TESTER PROFILOMETER II

SURFACE ROUGHNESS TESTER/PROFILOMETER Model No. SRG-4600   SRG-4600 PORTABLE SURFACE ROUGHNESS TESTER/ PROFILOMETER The newest addition to our state-of-the-art surface roughness testers /profilometers, the SRG-4600 will instill the highest level of...

DOLLY-CONCAVE EXTERNAL DIAMETER

Concave Dollies for the exterior surface of pipes.  Come in various diameters.  Requires approximately 3 weeks for delivery.  Reuseable.

NIST Surface Roughness Reference Standards/Profilometer Standards

Surface Roughness Reference Standards/Profilometer Standards/Surface Finish Standards Model No. SRG4600-500 Features High quality calibration standard for portable surface roughness gauges. Ra values of 119.5 and 16.1; individually serialized and...

AT DOLLY

DolliesLoading fixtures, stubs for adhesion testing. Choose from the following sizes and quantities: Size Quantity Order Code 10 mm 10 DOLLY10 14 mm 10 DOLLY14 20 mm 10 DOLLY20 50 mm 4 DOLLY50 Dolly MultipacksLarger quantity...

DOLLY-CONVEX INTERNAL DIAMETER

Custom sized dolies for curved surfacs.  Specifiy curviture.  Generallt a 3 week lead time.